features low cost high surge capability solderable electrode surface ideal for hybrids mechanical polarity : bottom or upper electrode denotes cathode according to the notice in package maximum ratings and electrical characteristics rating at 25 unless otherwise specified. single phase,half wave,60hz,resistive or inductive load . for capacitive load,deraate current by 20% jd jd jd jd jd jd jd 100005 10001 10002 10004 10006 10008 10010 maximum recurrent peak reverse voltage v rrm 50 100 200 400 600 800 1000 v maximum rms voltage v rms 35 70 140 280 420 500 700 v maximum dc blocking voltage v dc 50 100 200 400 600 800 1000 v peak forward surage current 8.3ms single half sine-wave superimposed on rated load i fsm a maximum instantaneous forward voltage at rated forword current) v f v tyical junction capacitance per element(note1) c j pf typical thermal resistance (note2) r ja /w operating temperature range t j storage temperature range t stg 4.type were denoted in the notice of the package 5.the typical data above is for reference only( ?). rev. 7, 13-mar-2017 3.thermal resistance from junction to ambient silicon rectifiers glass passivated rectifiers -55to+150 notes:1.measured at 1.0 mhz and applied voltage of 4.0v dc. 2.when mounted to heat sink from body. 10 300 1 -55to+150 400 characteristics symbol 1000 maximum average forward ( note 2 rectified current @tc=55 if (av) maximum dc reverse current @t a =25 (at rated dc bolcking voltage ) @t a =125 100 i r 1.1 jd100005 thru jd10010 a ua reverse voltage - 50 to 1000volts forward current -100 amperes unit 1.622(41.2) 1.606(40.8) 0.199(5.05) 0.195(4.95) 0.953(24.2) 0.937(23.8) 0.500(12.7) 0.461(11.7) dimensions in inches and (millimters jd 0.101(2.56) 0.100(2.54) 0.216(5.5) 0.154(3.9) 0.138(3.5) 0.098(2.5)
the cruve graph is for reference only, can't be the basis for judgment( ?)! rev. 7, 13-mar-2017 rating and characteristic curves jd100005 thru jd10010 single phase half wave 60hz resistive or inductive load 60 40 20 100 80 average forward current , amperes fig.1-forward current derating case temperature, 125 0 25 50 75 100 150 175 capacitive load ipk/iav=5,10and 20 5 10 20 number of cycles @ 60hz peak forward surge current , amperes fig.2-maximum non-repetitive surge current 1000 10 11 0 100 500 200 100 50 0.1 tj=25 tj=150 t j =25 pulse width:300us volts instantaneous forward current ,(a) fig.4-typical instantaneous forward characteristics 10 1.0 0.1 0.6 1.4 1.7 2.0 2.3 2.6 0.9 1.1 1000 100 percent of rated peak reverse voltage,(%) capacitance ,(pf) fig.3-farword current deating curve 1000 10 0.1 100 1.0 40 80 120 tj=150 tj=25 capacitance, p f fig.5-typical junction capacitance 1000 100 t j =25 reverse voltage,volts 500 200 50 10 0.1 1 100 10
legal disclaimer notice all specifications and data are subject to be changed without notice to improve reliability function or design or other reasons. hy makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the co- tinuing production of any product. to the maximum extent permitted by applicable law, hy disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special,consequential or incidental d- amages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merch- antability. statements regarding the suitability of products for certain types of applications are based on hy?s knowledge of typical require- ments that are often placed on hy products in generic applications. such statements are not binding statements about the suitabi- lity of products for a particular application. it is the customer?s responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application.parameters provided in datasheets and specific- ations may vary in different applications and performance may vary over time. all operating parameters, including typical paramet- ers, must be validated for each customer application by the customer?s technical experts. product specifications do not expand or otherwise modify hy?s terms and conditions of purchase, including but not limited to the warranty expressed therein. except as expressly indicated in writing, hy products are not designed for use in medical, life-saving, or life-sustaining applicati- ons or for any other applications in which the failure of the hy product could result in personal injury or death. customers using or selling hy products not expressly indicated for use in such applications do so at their own risk.please contact authorized hy pers- onnel to obtain written terms and conditions regarding products designed for such applications. no license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of hy. product names and markings noted herein may be trademarks of their respective owners. ?????????? hy ???????????hy (i) ? ??????(ii) ???????(iii) ??? ???????? ????? hy ? hy ???????????? ???????????????? ????? ????????????? ??? hy ???? hy ???? ?hy ????? hy ??????? ?????? hy ????????hy ?? ? ? hy ??????????????????? ??? rev. 2, 16-mar-2017 disclaimer
|
